Easy APRS

My position About ☰

reset

VK2LJ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2LJ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1735904166	13.42 Volts	37.85 Deg.C
1735903867	13.39 Volts	37.85 Deg.C
1735903568	13.42 Volts	38.34 Deg.C
1735903268	13.42 Volts	38.34 Deg.C
1735902968	13.42 Volts	38.34 Deg.C
1735902669	13.39 Volts	38.34 Deg.C
1735902370	13.39 Volts	38.83 Deg.C
1735902070	13.42 Volts	38.83 Deg.C
1735901769	13.42 Volts	38.34 Deg.C
1735901469	13.42 Volts	38.83 Deg.C
1735901170	13.39 Volts	38.83 Deg.C
1735900870	13.42 Volts	38.83 Deg.C
1735900570	13.42 Volts	39.32 Deg.C
1735900271	13.42 Volts	39.32 Deg.C
1735899972	13.42 Volts	39.32 Deg.C
1735899672	13.42 Volts	39.32 Deg.C
1735899370	13.42 Volts	39.32 Deg.C
1735899071	13.42 Volts	39.32 Deg.C
1735898771	13.42 Volts	39.32 Deg.C
1735898472	13.42 Volts	39.32 Deg.C
1735898172	13.39 Volts	40.79 Deg.C
1735897873	13.39 Volts	39.81 Deg.C
1735897573	13.39 Volts	39.81 Deg.C
1735897273	13.39 Volts	39.81 Deg.C
1735896972	13.42 Volts	39.81 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)