Easy APRS

My position About ☰

reset

N0PRG-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0PRG-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vaux*	Vmain*	Pi_temp*
1734909551	12.18 Volts	0.01 Volts	32 Deg.C
1734909252	12.18 Volts	0.01 Volts	32 Deg.C
1734908951	12.19 Volts	0.01 Volts	32 Deg.C
1734908651	12.19 Volts	0.01 Volts	31 Deg.C
1734908351	12.2 Volts	0.01 Volts	32 Deg.C
1734908052	12.2 Volts	0.01 Volts	32 Deg.C
1734907751	12.2 Volts	0.02 Volts	32 Deg.C
1734907451	12.21 Volts	0.01 Volts	32 Deg.C
1734907330	12.21 Volts	0.01 Volts	32 Deg.C
1734907032	12.21 Volts	0.01 Volts	32 Deg.C
1734906732	12.21 Volts	0.01 Volts	33 Deg.C
1734906430	12.23 Volts	0.01 Volts	31 Deg.C
1734906085	12.23 Volts	0.01 Volts	32 Deg.C
1734905948	12.24 Volts	0.01 Volts	31 Deg.C
1734905649	12.25 Volts	0.01 Volts	31 Deg.C
1734905348	12.26 Volts	0.01 Volts	32 Deg.C
1734905048	12.27 Volts	0.01 Volts	31 Deg.C
1734904749	12.27 Volts	0.01 Volts	31 Deg.C
1734904448	12.28 Volts	0.01 Volts	31 Deg.C
1734904148	12.3 Volts	0.01 Volts	31 Deg.C
1734903848	12.31 Volts	0.01 Volts	31 Deg.C
1734903549	12.32 Volts	0.02 Volts	31 Deg.C
1734903250	12.33 Volts	0.01 Volts	30 Deg.C
1734902950	12.34 Volts	0.01 Volts	30 Deg.C
1734902650	12.35 Volts	0.01 Volts	30 Deg.C

*Used Equation Coefficients:

Vaux: 0, 0.01, 0

Vmain: 0, 0.01, 0

Pi_temp: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)