Easy APRS

My position About ☰

reset

HB9KBJ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HB9KBJ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	TempIn*
1734873201	11.87 Volts	9.38 Deg.C
1734871404	11.87 Volts	9.38 Deg.C
1734858832	11.98 Volts	13.78 Deg.C
1734857036	14.18 Volts	14.26 Deg.C
1734856895	14.15 Volts	13.29 Deg.C
1734856836	14.09 Volts	12.8 Deg.C
1734856773	14.18 Volts	12.8 Deg.C
1734856717	14.09 Volts	11.82 Deg.C
1734856705	14.18 Volts	11.82 Deg.C
1734856682	14.12 Volts	10.84 Deg.C
1734856550	14.09 Volts	10.84 Deg.C
1734856504	14.12 Volts	10.84 Deg.C
1734855924	14.15 Volts	10.35 Deg.C
1734855734	14.15 Volts	9.38 Deg.C
1734855723	14.09 Volts	9.38 Deg.C
1734855694	14.06 Volts	9.38 Deg.C
1734851291	11.72 Volts	9.87 Deg.C
1734847699	11.72 Volts	9.38 Deg.C
1734845903	11.72 Volts	9.38 Deg.C
1734844107	11.75 Volts	8.89 Deg.C
1734838719	11.72 Volts	8.89 Deg.C
1734836924	11.75 Volts	8.89 Deg.C
1734833331	11.72 Volts	8.89 Deg.C
1734826145	11.75 Volts	9.38 Deg.C
1734824348	11.75 Volts	8.4 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

TempIn: 0, 0.4888, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)